Back to Blog
How-to Guides 2026-11-02 Victoria Miniatures by Victoria Lamb 7 views

Female Rolled Sleeve Arms x6: Assembly and Painting Guide

Female Rolled Sleeve Arms x6: Assembly and Painting Guide

A step-by-step guide to assembling and painting the Female Rolled Sleeve Arms x6, with practical tips for arm swaps on 28mm female Guard conversions.

Quick answer

Assemble the arms by test-fitting each pair to your chosen torso before gluing, then paint the sleeves separately from the hands and weapons for clean results. Work in sub-assemblies and keep the rolled cuff as a distinct color band to make the sleeves read clearly at tabletop distance.

Why sub-assembly matters for rolled sleeves

Rolled sleeves create a natural break between the upper arm and the hand, which makes them ideal for painting in parts. If you glue the arms to the torso and the hands to the arms before painting, you will struggle to reach the inside of the elbow and the cuff line. Instead, keep the arm, hand, and weapon separate until the sleeve is fully painted.

This approach also lets you check the arm angle against the torso without committing to glue. Resin arms can be gently adjusted with heat if needed, but test-fitting first reduces the risk of a misaligned shoulder joint.

Dealing with the lack of option details

The product listing does not specify available option types, such as separate hand or weapon choices. That means you should plan your build around the five pairs included and decide early which arms will hold rifles and which will be used for other poses. If you need a specific hand position, check the product images carefully before assembly, as returns or exchanges may be limited once you start cutting and gluing.

Step-by-step assembly and painting

  1. Clean and inspect each arm: Remove any flash or mold lines with a sharp hobby knife and fine sandpaper. Check the shoulder socket and the hand area for excess resin. Common mistake: skipping the inside of the elbow, which is hard to reach later and can show paint buildup. Work under good light and wear a dust mask when sanding resin.
  2. Test-fit arms to your torso: Hold each arm against the torso without glue to check the shoulder angle and the gap at the joint. The arms are designed for Victoria Miniatures female Guard and popular plastic sci-fi troops, but small gaps may appear. Common mistake: forcing an arm into a pose that strains the shoulder, which can crack the resin later. If the fit is tight, sand the socket slightly rather than the arm.
  3. Attach arms to the torso: Use a small amount of superglue or two-part epoxy at the shoulder joint. Hold the arm in place until the glue sets, then check that both arms are level and the hands can meet a rifle naturally. Common mistake: gluing both arms before checking the rifle fit, which can leave the hands misaligned. Dry-fit the rifle between the hands before the glue fully cures.
  4. Prime the arms and torso: Spray or brush on a primer suitable for resin, such as a thin grey or white acrylic primer. Keep the coat light to avoid filling the sleeve folds. Common mistake: priming in humid or cold conditions, which can cause a fuzzy finish that obscures detail. Prime the arms separately from the hands if you plan to paint them different colors.
  5. Paint the rolled sleeves: Basecoat the sleeve in your chosen fabric color, then shade the folds with a darker wash or thinned paint. Highlight the raised roll of the cuff with a lighter tone to define the sleeve edge. Common mistake: painting the cuff the same color as the sleeve, which makes the rolled detail disappear at arm's length. Use a slightly lighter color on the cuff roll to make it pop.
  6. Paint hands and weapons: Paint the hands in a skin tone that matches your army, and paint the laser rifles separately before attaching them. Keep the rifle sub-assembly on a temporary holder for easy handling. Common mistake: gluing the rifle before painting, which makes it hard to reach the trigger guard and the hand grip. Paint the rifle and hands before final assembly to avoid touch-ups.
  7. Final assembly and varnish: Once the paint is fully dry, glue the hands to the arms and the rifle to the hands using a tiny amount of superglue. Apply a matte varnish to protect the paint, especially at the wrist and shoulder joints where handling wear occurs. Common mistake: using too much glue, which can squeeze out and frost the painted surface. Apply varnish before gluing if you want to avoid a glossy glue sheen.

Product facts

  • Female Rolled Sleeve Arms x6: Includes 5 different pairs of female arms with rolled sleeves and laser rifles, scaled for 28mm heroic troops. This gives you enough variety to arm a small squad or spread across multiple conversions without repeating the same pose.
    Female Rolled Sleeve Arms x6
    Female Rolled Sleeve Arms x6

Related Articles

Customer Service
Home
Products
Cart
Profile