Back to Blog
How-to Guides 2026-11-15 Victoria Miniatures by Victoria Lamb 9 views

Sister Medicus of the Last Lamp: Assembly and Basing Guide

Sister Medicus of the Last Lamp: Assembly and Basing Guide

A practical walkthrough for building and basing the Sister Medicus of the Last Lamp, from choosing between the two heads to pinning the body and finishing a 25mm round base.

A single character, two head options

The Sister Medicus of the Last Lamp is a single resin character kit. The supplied information lists four components: the Sister Medicus body, Head 1, Head 2, and a 25mm round base. That is a small, focused build, so the main decisions are which head to use and how to keep the figure stable on its base.

Because the kit includes two heads, you can choose the expression or pose that suits your collection before committing glue. The supplied information does not specify a particular head as the intended default, so treat both as equal options and dry-fit each one.

What the kit actually contains

  • Sister Medicus of the Last Lamp: The kit contains the Sister Medicus body, Head 1, Head 2, and a 25mm round base. Confirms the full parts list so you can check the bag before starting and plan a build that uses the supplied base.
    Sister Medicus of the Last Lamp
    Sister Medicus of the Last Lamp
  • Sister Medicus of the Last Lamp: This is a physical product made from high-quality 3D prints. Sets the expectation that you will work with printed resin parts, not a multi-part plastic sprue.

Cleanup and dry-fit before any glue

The supplied information does not include a cleanup procedure, so the steps below are general good practice for printed resin miniatures. Work over a tray and wear a dust mask if you sand or scrape.

  1. Check the parts against the list: Lay out the body, both heads, and the 25mm round base. Confirm nothing is missing before you start removing material.
  2. Remove any obvious print supports: Use flush cutters or a sharp hobby knife. Cut away from your fingers and let the offcuts fall into the tray.
  3. Test-fit each head on the body: Press Head 1 and then Head 2 into the neck area without glue. Note which one sits more naturally and whether either needs light sanding at the contact point.
  4. Check the body against the base: Stand the body on the 25mm round base. If the feet do not sit flat, identify the high spot before you glue anything.

Choosing between Head 1 and Head 2

The supplied information names the heads but does not describe their expressions or features. The practical approach is to compare them side by side on the body. Look at how each head meets the neck, whether the chin clears the chest, and which angle reads better from the distance you normally view your models.

If you plan to paint the face, pick the head whose features are easiest to reach with a brush. A head that sits slightly forward or turned can hide detail in shadow, so test both before you commit.

Pinning a single character for stability

A single miniature on a 25mm round base has a small contact patch, so pinning is worth considering. The supplied information does not confirm whether the body includes integral pegs or a slot, so inspect the feet and the base before drilling.

If the feet are flat and the base is solid, drill a small hole in one foot and a matching hole in the base, then glue a short piece of paperclip or brass rod into both. If the body already has a mounting peg, test it in the base first; you may not need to pin at all. Do not drill through a hollow base without checking its thickness.

Basing on the supplied 25mm round base

The kit includes a 25mm round base, so you can build the model as supplied without sourcing a separate base. The supplied information does not describe the base top, so check whether it is plain or textured before adding basing material.

For a character model, keep the base simple so the figure stays the focus. A thin layer of texture paste or sand, a few small stones, and a painted rim are enough. Leave the area under the feet clear until the body is glued down, then fill around the feet afterward.

Assembly order that avoids rework

  1. Clean and dry-fit all parts: Complete cleanup and test both heads before any glue. This is the point where you can still change your mind without cutting.
  2. Pin or glue the body to the base: If pinning, drill and fit the pin first. If gluing directly, use a small amount of cyanoacrylate and hold the body upright until it sets.
  3. Attach the chosen head: Apply glue only to the neck contact point. Hold the head in position and check the angle from the front and side before it sets.
  4. Add basing material around the feet: Once the body is fixed, texture the base up to the feet. Avoid burying detail you want to paint.

Painting a medicus miniature

The supplied information does not include a color scheme or chapter markings, so the palette is your choice. For a medicus character, a limited palette helps the figure read clearly: one main uniform color, a secondary accent, and a skin tone. Keep the most contrasting color for the area you want viewers to notice first, such as the head or a shoulder pad.

Paint the body before attaching the head if the neck area is tight, then touch up the join afterward. If you have already glued the head, paint from the inside out: skin first, then the collar, then the outer layers. The 25mm base is small enough that a simple rim color keeps the model looking finished.

Where the supplied information stops

The supplied records do not include resin cleanup instructions, assembly steps, paint recipes, or compatibility notes for other kits. The guidance above is general practice for printed resin miniatures, not a manufacturer procedure. If you are unsure about a step, test on a hidden area first and keep the two heads unglued until you are satisfied with the fit.

Related Articles

Customer Service
Home
Products
Cart
Profile